![]() ![]() ![]() Push the Flow Meter, fittings, and pipe together firmly while twisting the fittings to the insertion marks (white lines).Install so the arrows on the side and face of the Flow Meter are oriented with the direction of water flow.Use the deburring tool or sandpaper to remove rough edges and debris inside and outside the pipe.Make a clean, straight cut on the two innermost marks (denoted with X's).ĭo not cut the pipe on the outer insertion marks.Mark 1 inches above the top mark to indicate insertion depth (white line).Mark 6½ inches after the first mark this will be the bottom cut (red line).Instructions for cutting ¾ inch and 1 inch PVC or PEX pipe Mark 1 ⅛ inches below the bottom mark to indicate insertion depth (white line).īottom fitting can be buried up to 1 inch if needed.Mark 1 ⅛ inches above the top mark to indicate insertion depth (white line).Mark 6¼ inches after the first mark this will be the bottom cut (red line).Identify 14 inches of straight pipe between the backflow preventer and the valve box.Instructions for cutting 1 inch copper or poly pipe Mark 1⅛ inches below the bottom mark to indicate insertion depth (white line).īottom fitting can be buried up to 2 inches if needed.Mark 1⅛ inches above the top mark to indicate insertion depth (white line).Put a small X next to the first two marks.Mark 8½ inches after the first mark this will be the bottom cut (red line).Mark 6 inches after the backflow this will be the top cut (red line).Identify 16 inches of straight pipe between the backflow preventer and the valve box.Instructions for cutting 3/4 inch copper or poly pipe ![]() If you are not using the Rachio-recommended fittings, please use your fittings' specs to complete installation. Reference the matching pipe cutting instructions in the following pages to mark pipes in preparation for cutting. Use the chart on the next page to find the size and material of your system. Push the Flow Meter and fittings together firmly using a twisting action until the fittings are flush or nearly flush with the Flow Meter. Drain the system by running any zone for one minute using the Quick Run feature in the Rachio App.Turn off water to the irrigation system at the backflow or at the main shut-off.You will be guided through the pairing process and then prompted to continue installation. From the "More" tab, select "Accessories," then add the Rachio Wireless Flow Meter. Do not put the batteries in the Flow Meter until prompted.Take the Wireless Flow Meter to the backflow preventer where it will be installed.To find a Rachio Pro, go to /flow-install STEP 1: Pair flow meter. If you're unable to complete any of the installation steps, we recommend a professional installation. Using glue of any kind could damage the Rachio Flow Meter. Once attached, fittings cannot be removed from the Flow Meter, but may be removed from the pipe using fitting removers. Inserting your fingers into the Flow Meter or fittings can damage equipment or cause personal injury. Using installation methods other than those recommended in this manual could damage the Wireless Flow Meter or void the warranty. If you have more than one Rachio 3 controller or more than one backflow preventer, visit /flow-advanced.System must have ¾ inch or 1 inch pipe made of either copper, PVC, PEX, or SDR9 poly.įor 1 inch PVC pipe, 1 inch copper or poly pipe, and ¾ inch PVC pipe, you will need 14 inches of straight pipe between the backflow preventer and valve box.įor ¾ inch copper or poly pipe, you will need 16 inches of straight pipe between the backflow preventer and valve box.The Flow Meter is not rated for potable water and must be installed after the backflow preventer.For more information, visit /flow-underground. Backflow preventer and installation area must be above ground (recommended).īelow ground installation requires additional steps not included in this manual.Installation site must be within 300 feet of an installed Rachio 3 Smart Sprinkler Controller.Visit /flow for a list of required tools, helpful videos, FAQs and more.īefore any pipe is cut, make sure your system meets the installation requirements: Installation instructions are intended only for use with recommended fittings. Rachio Wireless Flow Meter Quick Start Guide ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |